Test Software Interface (Descriptive Translation)

Testing requirements

The test should be carried out at an ambient temperature of 20℃±5℃. Place the fully charged battery on two planes, and the extrusion pressure is 13KN±0.78KN, perpendicular to the direction of the plate. Once the pressure reaches the maximum, the extrusion test can be stopped. During the test, the battery is qualified if there is no external short circuit, explosion, or fire.

1. For cylindrical batteries, the longitudinal axis of the extruded battery should be parallel to the two plates of the extrusion device.
2. Only the wide side of the battery is squeezed for square and soft-pack batteries.
3. For button batteries, the upper and lower planes of the battery are parallel to the flat plate during the extrusion test.
4. High-temperature resistant steel needle, steel needle (needle tip angle 45°~60°, smooth needle surface, no rust, oxide layer, and oil stains), penetrate at a speed of (25±5) mm/s from the direction perpendicular to the battery plate. The penetration position should be close to the geometric center of the punctured surface. The steel needle stays in the battery and observes for 1 hour.

Specification of Battery Extrusion Needling Test Machine

1. Inner box size: 520x450x560mm WDH
2. Machine size: 800x700x1730mmWDH
3. Inner chamber material: SUS201 stainless steel plate, thickness 1.2mm and coated with Teflon;
4. The outer box material: 1.5mm thick cold-rolled steel plate baking paint treatment;
5. Observation window: 250x250mm,
   Two-layer tempered glass, transparent window is equipped with stainless steel mesh;
6. Smoke outlet: diameter of 100mm, located at the back of the machine;
7. Pressure relief port: The opening size is 200x200mm and is located at the back of the chamber. When the sample explodes, the pressure relief will be released;
8. Door: The single door is left open, the door is equipped with a safety limit switch, and the side is equipped with an explosion-proof chain. The equipment can be operated only after closing the door to ensure the safety of personnel;
9. Test hole: There is a 50mm diameter test hole on the left side of the device, which is convenient to put the temperature, voltage, and current collection line;
10. Lighting device: easy to observe the state of the tested sample;
11. Drive mode: servo motor drive
12. Control mode: touch screen control
13. Extrusion acupuncture parameters:
    *For cylindrical batteries, the longitudinal axis of the extrusion battery should be parallel to the two plates of the extrusion device;
    *For square and soft pack batteries, only the wide side of the battery is squeezed;
    *For coin or button-type batteries, the upper and lower planes of the battery are parallel to the flat plate for the extrusion test;
    *Through the direction perpendicular to the battery plate (steel needle stays in the battery);
14. Pressure range: 1-20kN
15. Pressure display accuracy: 0.1N
16. Sensor resolution: 1/1000;
17. Unit conversion: kg, N, lb
18. Test maximum battery size: 200x200x200mm WHD
19. Extrusion stroke: 250mm
20. Speed: 1-40mm/s adjustable
21. Holding time: 0-99H99(H/M/S can be arbitrarily set)
22. Extrusion head: standard flat plate extrusion head, area ≥20cm²
23. Extrusion degree: extrusion pressure up to 13±0.0.78kN;
24. Sample clamping method: manual clamping, fixture to meet the button type, cylindrical, square battery
25. Weight: 100kg
26. Power supply: AC220V
27. Power: 1KW

UN38.3,UL1642,UL2054,GB 8897.4-2002,IEC60086-4 ,GB31241,SN/T1414, SN/T1413 , YD1628, GJB2374, QB/T2052,IEC62133-2012, SAE-J2464,GB31241,IEC62133-2012 ,IEC 62281: 2006 ,IEC 60086: 2007 ,IEC 61960

1. Avoid sunlight shine directly or high temperature and wet.
2. Place on smooth ground.
3. The power supply is a three-phase, five-wire power supply that can be ground.
4. Please make sure that the environment temperature is 20±5 degrees when using. It can ensure the casing test temperature.

The main function of this equipment is to test the physical and other related properties of vehicles such as passenger cars, buses, tractors, motorcycles, and their parts under the cleaning process conditions of high pressure/steam jet cleaning. After the test, check to judge whether the performance of the product meets the requirements. It can help with the design, improvement, verification, and factory inspection of the product.

1. 38Water resistance test method
2. IEC60068-2-68 Water resistance test method
3. GB/T 4208 Water resistance test method
4. IEC60529 Water resistance test method

1. The dust test chamber formed using a CNC machining box has an excellent shape, does not react with the handle, and is easy to operate.
2. Imported high-grade stainless steel inner tank (SUS304) mirror panels, use A3 steel box outside the gall spray. So, it can increase the appearance of the texture and cleanliness.
3. Equipment containing vertical dust circulation air dust can be reused for testing. The device itself has a good sealing performance. And the test laboratory can observe the situation. The device is equipped with a vacuum system to meet the needs of the test. Equipment dust at the bottom of the device can be replaced,
4. Large observation window with bright lights to keep the box. And the use of tempered glass embedded heating element, at any time, a clear observation box condition.
5. This dust chamber is externally connected to test power lines or signal lines. The test was carried out with a 50mm diameter hole.

• Led lights
• Metal Parts
• Electronics
• Car Spare Parts
• Battery Pack

1. The battery test machine is used for testing the fire resistance of the battery.
2. The result is according to the fire time to determine the fire resistance capability.
3. The test finishes when the burning battery explodes or burns away.

1. The wire is enclosed with a metal fireproof cover, which is available to prevent flame during the testing process.
2. The lighting system is designed to observe the internal testing process.
3. Nail Penetration/Crush Force is controllable within 250N to 13KN and meets different standards.
4. A wire hole can test internal temperature or air pressure, while a vent hole with an air blower can discharge the exhaust air.
5. The control system employs an independent control cabinet and is separated from the test chamber by a distance of 1-2 meters. So it can reduce the noise and improve safety.

1. Battery drop test for the face of the package, Angle, and edge for the free drop test. It has a digital display and a high display decoder to track height and drop height. So it can accurately give products with preset drop height error of less than 2%, or 10 mm.

2. The battery drop test machine adopts a single-arm double-column structure. It has an electric reset, electric control drop, and electric lifting device. This battery drop test equipment is easy to use.

3. The unique hydraulic buffer device dramatically increases the machine’s service life, stability, and security.

1. This battery impact tester adopts a double rail structure. Sudden power failure can protect the testing machine.
2. The impact weight can be easily replaced, installed, and disassembled. It provides an excellent solution for handling errors caused by secondary shocks. At the same time, the test accuracy is improved.
3. There is a metal fire shield attached to the wire. Burning is thus prevented during the test.
4. The lighting system is designed to observe the internal testing process.
5. Height digital display, controllable height 25-1000mm.
6. The wire hole allows testing of the internal temperature or air pressure. Exhaust vents with blowers allow exhaust to escape.
7. The control system adopts an independent control cabinet 1-2 meters from the laboratory. This reduces noise and improves safety.

1. The wire is enclosed with a metal fire-proof cover. It is available to prevent the flame during the testing process.
2. The lighting system is designed to observe the internal testing process.
3. Nail Penetration/Crush Velocity with a controllable range of 10~80mm/s.
4. Nail Penetration/Crush Force is controllable from 250N to 13KN.
5. Wire hole provides a possibility to test internal temperature or air pressure. A vent hole with an air blower can discharge the exhaust air.
6. The control system employs an independent control cabinet separated from the test chamber at 1-2 meters. So it can reduce the noise and improve safety.