Machine Introduction
This is a high-precision and high-performance battery tester. It can set parameters in the computer software. It can charge and discharge various batteries for testing battery capacity/voltage/current, and do battery cycle testing. Traditional linear equipment, high precision stable performance. Single-point control, using constant current source and constant voltage source double closed-loop control. It is convenient and flexible to connect with the computer through Ethernet, and more devices can be added at any time through the switch.
Features of 5V 6A 8 Channels Battery Testing Equipment
- 220V50HZ, support 110V customization
- Network cable interface to connect to the computer
- Traditional linear, high precision, stable
- Support hardware anti-reverse connection protection
- Software over-current/over-voltage/under-voltage protection
- The software interface is simple and easy to operate
- Support switching between Chinese and English
- 1000-1000 precision, can do 10000-50000 precision
- Independent control of each channel
- Modular structure, long life
Technical Parameters
| Device model | XB-OTS-5V6A-8CH | |
| Number of device channels | 8 | |
| Channel control method | Each channel is independently controlled, and the current and voltage four-wire system collects more | |
| Channel Features | Constant current source and constant voltage source adopt double closed-loop structure | |
| Input resistance | ≥1MΩ | |
| Channel interface | The same interface for charging and discharging, different ports can be customized | |
| Channel Isolation Characteristics | The channels share the ground, different channel fixtures cannot be contacted, and isolation customization is supported | |
| Voltage
scope |
Charge | 10mV-5V (device port) |
| Discharge | 1.3V-5V(device port), the minimum discharge voltage is related to the length of the line, and the deep discharge device can be customized1V-5V | |
| Voltage accuracy | ±0.1% of FS, Ambient temperature 15°C-35°C, other precision can be customized | |
| Current
scope |
Charge | 12mA-6A, Dual range can be customized |
| Discharge | 12mA-6A, Dual range can be customized | |
| Current accuracy | ±0.1% of FS, Ambient temperature 15°C-35°C, other precision can be customized | |
| Power | Single channel output power | 30W |
| Stability | 0.2% of FS | |
| Time | Current response time | ≤10ms(90% range response time) |
| Data record | Recording frequency | 1Hz，Customizable 10HZ |
| Data recording conditions | Minimum time interval: 1S | |
| Minimum voltage interval: 1mV or (related to the voltage range, 0.01% of the voltage range) | ||
| Minimum current interval: 1mA or (related to the current range, 0.01% of the current range) | ||
| Charge | Charge Mode | Constant Current Charge、Constant Voltage Charge、 Constant Current and Constant Voltage Charge、CPC |
| End Condition | Voltage、Current、 Relative Time、Capacity、 – △V | |
| Discharge | Discharge Mode | Constant current discharge, constant power discharge, constant resistance discharge |
| End Condition | Voltage、Current、 Relative Time、Capacity、 – △V | |
| Pulse | Charge | Constant current mode, constant power mode |
| Discharge | Constant current mode, constant power mode | |
| Min Pulse Width | 5S or above is recommended | |
| End Condition | voltage, relative time | |
| DCIR | DCIR （Optional） | Support user-defined points for DCIR calculation |
| Cycle | cycle test | 399 commands can be set, and 65535 cycles can be set |
| loop nesting | Support 5 layers of loop nesting | |
| Protection | Software protection | Support power-down data protection (with UPS power supply, 100% guarantee no data loss） |
| Support for continuous start | ||
| Overvoltage protection, undervoltage protection, capacity protection, overcurrent protection, undercurrent protection | ||
| Anti-reverse protection | ||
| Data export method | Excel、PDF | |
| Cooling method | Air cooled | |
| Noise | ≤50dB | |
| Dimension | 47x40x14cm (length, width and height) before packing
55x50x23cm after packaging (length, width and height) Packaged weight 12kg |
|
| Communication method with host computer | Network interface, one computer can control multiple devices through a switch, and the network interface can be converted into a USB interface through a USB wired network card | |
| System Requirements | windowsXP and above | |
| Software Control Quantity | The device is connected to the device through 485 or a switch, and one computer can control more than 100 devices | |
| Other | BMS communication protocol can be customized, and other communication methods can be customized | |
High Precision Battery Test Machine Working Environment
| Range of working temperature | 0℃-40℃ |
| Storage temperature range | -10℃-50℃ |
| Working environment relative humidity | ≤70% RH (no condensation) |
| Storage environment relative humidity | ≤80% RH (no condensation) |
| Input active power | 300W |
| Input power | AC220V±10%/50Hz Maximum 2A, other power specifications can be customized |
Software Introduction
The operation interface is as follows, including testing, calibration, allocation group, equipment management, data management, Chinese and English switching, etc.
